How To Put A VW Passat Into Service Position
All information and images © copyright of Blaufergnugen Inc.
DISCLAIMER: Blauparts recommends that an Audi VW Factory Trained ASE Certified Technician perform repair.
Always read the factory service manual safety instructions and guidelines. Always wear safety glasses and other safety items when performing the following repair.
How To Step 1
Elevate vehicle on an automotive lift or jack stands, using proper lift points as outlined in the owners manual.
Remove the lower splash pan.
How To Step 2
Remove the lower drivers and passengers side bumper grilles. Reach in behind the fog light and unplug the electrical connectors.
How To Step 3
Remove the main hood latch mechanism by removing the (3) 10mm fasteners and the electrical plug.
Additionally, remove the secondary hood release lever. Pry up and remove the spring clip from the hood latch lever, then use a flat blade screwdriver to spread the latch apart so that the rod clears the latch pins. Next, remove the latch and place it off to the side.
How To Step 4
Remove the main grille by removing (2) Torx head fasteners, one located at each side of the grille. Firmly pull up on the grille until the grilles lower mounting tabs pop out.
How To Step 5
With the main grille removed, locate and remove the (4) Torx screws found in lower grille cavity.
How To Step 6
Locate and remove the fasteners located on the forward side of each wheel well. You will find a total of (4) fasteners in each wheel well, with one being rather hidden toward the very top of each wheel well as pictured.
How To Step 7
Remove the bumper cover by firmly pulling the cover forward, one side at a time. While pulling the bumper cover forward, you will need to unplug the electrical connectors for the amber side indicator lamps, found on each side of the bumper.
How To Step 8
Locate and remove the (5) fasteners that hold the upper plastic bumper cover reinforcement, also the (2) fasteners holding the lower steel bumper cover reinforcement.
How To Step 9
Remove the upper outer fasteners from the bumper shock brackets on each side of vehicle, replace fasteners with special tool 3411. Once installed, remove all remaining fasteners from bumper shock brackets.
How To Step 10
Remove the (2) fasteners that hold the air box intake tube in place, then pull upward on intake tube to completely remove it.
How To Step 11
Remove the upper radiator valance fastener located at the forward fender edge on each side of vehicle.
How To Step 12
Locate and remove (2) fasteners holding the fender to the radiator valance, one fastener found under each headlamp.
How To Step 13
Locate the radiator drain screw at the lower front driver side of the radiator. Drain the coolant from the system into a suitable drain pan.
How To Step 14
Drain the coolant out of the radiator by opening the drain screw found on the lower
drivers side of the radiator.
How To Step 15
Remove the lower intercooler hoses from the intercooler crossover pipe.
How To Step 16
Remove the upper and lower radiator hoses by gently prying on the removal clip
integrated into the hose clamp with a screwdriver blade.
How To Step 17
Slide entire radiator and front support assembly forward on the pair of previously
installed special tool 3411.
Service BulletinsImportant Repair Information.
Please read the
following bulletins BEFORE beginning timing belt service.
- Subject: How to prevent premature water pump failure? Proper cooling system service procedures.
- Subject: How to prevent inadvertent damage to the pulley key? Proper front crankshaft timing belt pulley removal.
- Subject: How to prevent irreversible damage to the hydraulic tensioner damper? Proper hydraulic tensioner damper installation.
QuestionsDo you have a specific question regarding 2.8L VW Passat front bumper removal or how to put into service position?
Troubleshooting GuideCommon installation problems.
Technical Help Coming Soon!
BLAU® Official O.E. INA VW Passat Timing Belt KitsOur goal is to make your VW Passat timing belt repair job a success. Preventing any possible problems during this crucial repair is our number one priority. Over 27 years of VW German heritage and small family owned business way of thinking has strongly influenced our Gen II BLAU® VW Timing Belt Replacement Kits.
Related VW Passat Timing Belt Replacement Information
Cost of ReplacementHow long does it take and how much will it cost to replace the timing belt on my VW Passat with 2.8L engine?
BLAU® Official O.E. ComponentsWhat are the brand names of the timing belt components that originally came on my VW Passat 2.8L 30 valve?
Change IntervalsWhat is the factory recommended timing belt interval for VW Passat 2.8L 30 valve engines? How long will new timing belt parts last after replacement?
Special ToolsDo I need special tools to replace the timing belt on the VW Passat 2.8L engine? Can I do it without the tools?
Related ReplacementCan I just replace the timing belt? What other parts should be replaced during VW Passat timing belt service?