New Feature! Ask Us A Control Arm Replacement QuestionWe have a new helpful feature on this page. Do you have a question regarding how to replace your control arms? Submit a question and we'll be happy to answer it using our years of tech experience. Check it out at the bottom of this page, or CLICK HERE!
This page is designed to answer some "HOW TO" questions on removing and replacing VW Passat control arms. It contains information on what an VW mechanic will be doing during an VW control arm maintenance job.
Blauparts VW control arm replacement information is not designed to be an instruction sheet. This is an overview on removing and replacing VW Passat control arms and was designed to help our customers grasp what's involved and helps owners to better communication with the mechanic during the VW control arm service job. The below VW control arm replacement info will differ depending on vehicle application and which VW Passat control arms are being replaced.
Replacing VW Passat control arms one by one can cost more in the long run. You'll save on installation costs when replacing all of your VW Passat control arms at once. If some of the control arms are on their way out, the others aren't far behind. It can be frustrating to replace a few VW Passat control arms only to find yourself back at the mechanic complaining of another squeaky control arm.
In the event of VW control arm failure, look to the nation's leading VW control arm specialist for the solution. Get the job done right the first time by replacing all of your VW Passat control arms, tie rod ends, sway bar links, and hardware with our complete Offficial O.E. Ocap BLAU Control Arm Replacement Kits.
Replacing any suspension components on your automobile without having proper knowledge, mechanical ability or the proper tools and safety equipment, can cause severe injury, damage, or death. Blauparts recommends that you have an A.S.E. Certified VW Technician install your parts to ensure safety. Always wear safety galsses and other safety items when performing automotive service work.<br > <br > ALWAYS: Refer to the factory manual for proper safety instructions, precautions, and proper installation of the components. NOTE: The guidelines below are not intended to replace the instructions as outlined in the Factory Bentley Manual. If you do not have the Factory Bentley Manual we recommend that you purchase one before beginning your installation project.
Estimated Time To Replace & Install VW Passat Control Arms
Below HOW TO steps 1-10 will take approximately 3.0 to 4.5 hours per side.
Overview Of How To Remove And Install VW Passat Control Arms
This information is not intended to replace the factory manual. Please refer to the factory manual for detailed instructions
- HOW TO 1<br > <br > <br > <br > Loosen the upper control arm ball joints from the top of the wheel bearing housing. Be careful, the long bolt that secures the upper control arm ball joints to the wheel bearing housing is sometimes difficult to remove. <br >
- HOW TO 2<br > <br > <br > <br > Remove the sway bar link which is attached to the front lower control arm.
- HOW TO 3<br > <br > <br > <br > <br > Loosen the upper control arm mounting plate. This is done by removing the 3 bolts in the engine compartment that secure the upper control arm mounting plate to the body of the car. Note: The top of the VW shock tower also secures to the control arm mounting plate.
- <br > <br >
- HOW TO 4<br > <br > <br > <br > Remove the lower shock bolt from the front lower control arm.<br >
- HOW TO 5<br > <br > <br > <br > <br > From the wheel well area pull out the upper control arm plate far enough away from the body of the car to allow room for the removal of both forward and aft (rear) control arm bolts. Loosen the inner control arm bolts.
- <br > <br >
- HOW TO 6<br > <br > <br > <br > <br > Remove the lower control arms from the lower portion of the wheel bearing housing. The lower control arm ball joints have tapered shafts, as a result of this design they are wedged tight in the wheel bearing housing. Special tools are recommended to separate the control arm ball joint shafts from the wheel bearing housing to prevent damaging the ball joint boots on the control arms. Note: If the control arm ball joint boots are damaged, we have a control arm ball joint boot repair kit.
- HOW TO 7<br > <br > <br > <br > Remove the tie rod end bolts and loosen the tie rod end from the wheel bearing housing.<br >
- HOW TO 8<br > <br > <br > <br > Remove the drive axle bolt and brake caliper from the wheel bearing housing.
- HOW TO 9<br > <br > <br > <br > Remove both forward (front) and aft (rear) lower control arm bolts from the sub frame.
- <br > <br > HOW TO 10<br > <br > To reassemble you will be repeating step 9-1 in reverse.<br > <br > HOW TO 11<br > <br > When VW control arm installation is finished a complete wheel alignment is necessary!
Most discerning VW and VW owners carefully research and choose high quality control arms. Blauparts have teamed up with Ocap, a renowned Italian company that specializes specifically in the area of steering and suspension parts. Partnership with an O.E. manufacturer means Blauparts can ensure absolute quality control through a direct supply chain.
Ocap of Italy is a certified Official O.E. (original equipment) supplier. This means that they're a direct supplier of suspension componentsfor VAG (Volkswagen VW Group), along with their other exotic high performance companies Lamborghini, Bugatti, McLaren, Lotus, Renault Sport, and Porsche straight off the production line. They also supply Maserati, Mercedes, Volvo, and BMW. Ocap is also certified by TUV (Germany): UNI ISO-9001, TS 16949 (Quality System) and ISO 14000 (Environment System). Read more about Ocap at www.ocap.it.
BLAU® Ocap Control Arm Replacement Kits feature arms that have been made under O.E. requirements: aluminium alloy 6082 material, bushings, ball pins, Klüber grease, rubber seal bellows, and plastic shells. Take advantage of the very best in quality control arms at Blauparts!
Blauparts employs statistical quality anaylasis with the philosophy of preventing problems before they're even detected. In a recent quality query for the previous 2011-2012 sales year we found that the return rate of Ocap control arms was only .0026%, way below 1%.