Audi Water Pump Replacement Information

When nearing a timing belt and Audi water pump replacement (60,000 - 90,000 miles), many owners carefully research different Audi timing belt kits and the individual components. We discuss symptoms of a worn or bad Audi water pump. What are the symptoms of a defective water pump? Did you recently install a new water pump and are now experiencing problems? What causes an Audi water pump to fail early? Do you want your Audi water pump to last 60,000 to 90,000? Common concerns and questions regarding Audi water pumps are addressed and explained.

Within this page, we will discuss symptoms of a worn or bad Audi water pump. Common statements and questions regarding Audi water pumps are addressed and explained. Here are some of the topics you will learn about on this page:

Symptoms Of A Worn or Bad Audi Water Pump

Leaking Audi water pump can cause engine damageWe've read some comments asserting that water pumps don't get weak, they catastrophically fail. Our decades of specialized Audi VW repair service have shown that like most mechanical parts, the water pump warns you when it needs attention. The internal bearing and seals of an Audi water pump can weaken and is the primary reason why a water pump eventually fails. The typical driver isn't always alert to what is going on under the hood and may be unaware of the water pump's health. However, an experienced mechanic who is familiar with Audi or VW engines can recognize the early signs of a weakening water pump. The most common symptom is a water pump leak. When unchecked, a leaking Audi water pump can eventually create a humming noise and possible engine overheating. In Blauparts' own Audi VW repair facility, experience has shown the most common causes of water pump failure to be: 1) age and/or high mileage and 2) a neglected coolant system that was not restored to the original factory intended condition during water pump replacement.

If it has been determined (not assumed) by visual water pump inspection that your Audi water pump is leaking, you should not continue driving the car. Continued driving with a leaking water pump (for an extended period) can be catastrophic. There is the possibility that the internal Audi water pump bearing will develop excessive play, causing a misalignment of the water pump pulley, allowing the timing belt to rub against other components, thus resulting in timing belt failure and engine damage (see image above). The Audi water pump impeller may also rub against the inside of the engine block, causing fragments and debris to contaminate the cooling system. If this debris or sediment is not thoroughly flushed from the cooling system when installing a new water pump, it will eventually lead to premature Audi water pump failure.

Audi Coolant System Contamination

Normal worn Audi water pumpPremature Audi water pump failure due to bad coolant flush

Image 1) Original water pump removed from an Audi 2.7T with approximately 80,000 miles. This pump was not leaking. Note the normal discoloration of the aluminum casting. This is the result of minimum coolant contamination for this type of mileage.

See Blauparts Audi water pump replacement special ‘Service Bulletin' pdf on the tech tips on how to prevent Audi cooling system contamination.

Image 2) Water pump removed from an Audi 2.7T with less than 3,000 miles due to leaking. It was wrongly assumed that it was a manufacturer defect. However, the evidence revealed that the leak was caused by coolant contamination. Note the abnormal black discoloration of the aluminum casting. The cause was a result of an additive (likely a flushing agent) containing muriatic acid/other acids being used (before or after the water pump replacement). Acids left in the coolant system ate away at the internal seals and caused premature water pump failure.

Crucial Audi Coolant Flush and Fill Information

Do you want your Audi water pump to last 60,000 to 90,000? Then, it is important to re-create the engine condition as it was when it left the factory. You cannot be lazy when it comes to the water pump and timing belt replacement! Cutting corners now adds time, labor, and money later.

It is the responsibility of the installer to take the necessary time to thoroughly flush the cooling system. It has been noted that due to time constraints, inconvenience, and profit, many individuals, mechanics, and repair shops do not take the extra time needed to thoroughly flush the entire cooling system before the installation of a new Audi water pump. Just draining the cooling system and refilling it is not enough! Thoroughly flushing the coolant involves the engine block, radiator, heater core, and hoses.

Premature water pump failure (bearings and seals) can occur if you don't take the time to flush the entire cooling system and its related components. Often when problems arise, such as a coolant leak, the new Audi water pump is blamed as the cause when in fact the opposite is true. It's usually because the installer has neglected to follow this important step.

Flushing the Audi Cooling System

The Audi cooling system MUST be thoroughly flushed of all accumulated silt and sediment buildup. All aftermarket cooling system additives or stop leak products that may have been added to the cooling system (past or present) should be completely flushed! Thoroughly flushing the coolant involves the engine block, radiator, heater core, and hoses.

Only use tap distilled water to flush the entire cooling system. Do NOT use cooling system flush products. Many of these agents contain muriatic and/or other acids. Remnants of these acids left in the cooling system can contaminate the new coolant and cause your new Audi water pump to prematurely fail (see Image 2).

Filling the Audi Cooling System

Use only Audi VW G12 antifreeze coolants which were included in your timing belt kit (G11 pre-1997). These bottles contain a coolant that is concentrated. You must dilute the coolant. Mix 50% coolant and 50% deionized water. Caution! Do Not mix normal tap water with new coolant. Tap water varies in PH and mineral content and depending on these factors, can contaminate the cooling system by making the coolant have an acidic PH value which can adversely affect your new water pump and cooling components. IMPORTANT: Read the warnings on the antifreeze coolant bottle regarding improper use being harmful or fatal. Check out our other detailed pages covering everything about Audi coolant antifreeze.

TIP: When topping off your cooling system, always use the OEM-approved Audi coolant and appropriate mixture ratios! Make sure that your local quick lube or mechanic isn't adding or topping off your system with incorrect coolant. Mixing OEM-approved coolant with any other coolant will cause an adverse chemical reaction with the existing coolant and contaminates the cooling system, thus affecting the longevity of the Audi water pump.

Audi Water Pump Leak

Common scenarios and questions regarding water pump leaks:
"I see coolant on the ground after the car has been running and is then parked. Could the water pump be leaking?"

"My Audi water pump appears to be leaking. What should I do?"

"I have a coolant leak. How do I know if it's my Audi water pump?"

Age, high mileage, or coolant contamination are the most common cause of water pump leaks.

Don't jump to conclusions. You can't assume that a puddle of coolant under the car is due to a leaking water pump. An experienced A.S.E. certified mechanic that is familiar with your model can best inspect and verify where a coolant leak is coming from.

The diagnostic starting point involves removing the splash pan. This will enable you to see where the coolant is pooling. The passenger side of the engine compartment, the center front of the engine, or the driver’s side? Common coolant leaks originate from coolant hoses and the expansion tank. The expansion tank often becomes brittle and leaks below its location (in front of the driver’s side wheel on most models).

When an Audi water pump is leaking, you'll usually find a trail of coolant from the water pump area down to the lowest point of the engine (depending on the model). Removing the engine covers and visually inspecting the water pump is necessary. On some engines such as the 2.8L and 2.7L, coolant may have pooled onto the surface of the front flat oil pan surface.

An Audi water pump usually leaks from the following areas:

Leaking from the Audi Water Pump Shaft Bearing or Seals

Age and/or high mileage is the most common cause of internal bearing and seals weakening or failing. Bad water pump bearings and seals usually cause a leak from the water pump shaft. Premature failure is typically due to contaminated antifreeze. Contamination is caused by not thoroughly flushing the coolant system, using flushing agents containing damaging acids, or using or mixing incorrect fluid with OEM approved.

See Crucial Audi Coolant Flush and Fill Information and Blauparts Audi Water Pump Replacement 'Service Bulletin' pdf.

Leaking from the Audi Water Pump Gasket Mating Areas

The key to a factory quality seal is in the preparation of the surface area. Take the extra time to properly clean the Audi water pump gasket and thermostat O-ring surfaces thoroughly. These surfaces should be free of all old gasket material and corrosion build-up before installing your new Audi water pump and thermostat. To achieve the optimal just like new surface, it's usually necessary to use a medium grit scotch brite pad and/or angle die grinder with a medium grit scotch brite conditioning pad (see the video below). When the water pump mounting surfaces are thoroughly cleaned and smooth, gasket sealing agents are not needed!

Audi water pump gasket mating surface, the right waySome installers have used sealing compounds that can significantly reduce the sealing function of the Audi water pump gasket. It is important to note that no sealing compounds were used when mating the water pump to the engine block from the factory. The factory Robert Bentley manual does not refer to using sealing compounds during water pump replacement. It is important to pay attention to and follow the manufacturer's installation instructions. Sealing agents (RTV Form-a-Gasket silicones, aerosol adhesives, or sealants) should NOT be used!

Premature leaking from the Audi water pump gasket mating area is almost always due to improper alignment during installation, mating surfaces not being prepared properly, or a sealing agent being used. Sealing agents (RTV Form-a-Gasket silicones, aerosol adhesives, or sealants) vary in composition and intended usage. When used in conjunction with composite paper gaskets, they negatively affect the gasket's ability to properly compress and perform the sealing function, rendering them ineffective (see image 3).

Although uncommon, the wrong type of coolant can eat away at the gasket and eventually cause a leak. Double-check all Audi water pump mounting bolts for tightness. A loose or missing water pump or thermostat housing bolt can also result in a leak. You can also watch the following video for helpful tips:

How to Properly Prepare the Audi Water Pump Gasket Mating Surface Video

Incorrect Use Of Water Pump Sealing Agents

Premature Audi water pump failure due to gasket sealing agentImage 3) Water pump removed from an Audi 3.0L with less than 5,000 miles due to leaking. The customer wrongly assumed that it was a manufacturer defect. However, the evidence revealed that the leak was caused by both using RTV gasket material and coolant contamination. Using RTV material can cause the gasket to slip, resulting in misalignment during installation, and producing a coolant leak. Sealing agents vary in composition and intended usage. When used in conjunction with composite paper gaskets, they negatively affect the gasket's ability to properly compress and perform the sealing function, rendering them ineffective. The abnormal coloration and thin film on the aluminum casting are evidence of acidic coolant contamination. See Crucial Audi Coolant Flush and Fill Information.

An appropriate gel-like gasket sealing agent should only be used when there is severe pitting of the engine block surface and an even or smooth water pump mounting surface cannot be achieved. Not because you're cutting corners and don't want to take the time to clean the surfaces properly. An Audi Allroad 2.7L Turbo engine is shown in this video.

Regarding 1.8L engines, the same theories illustrated in this video apply. Installers need to take the extra time to correctly prepare the water pump O-ring area to ensure a factory quality seal. Be sure to clean all old O-ring material, built-up residue, loose debris, and prepare the surface using a medium grit scotch brite pad. Experience has shown that when not properly prepared the new 1.8L water pump O-ring may not seal evenly, resulting in possible hairline coolant leaks. In addition, sealing agents (RTV Form-a-Gasket silicone, aerosol adhesives, or sealants) should not be used. We reference a 1.8L water pump in the video which illustrates the improper use of such RTV material. The example shows how stray RTV can let loose and clog internal components such as the heater core.

Leaking from the Audi Water Pump 'Weep Plug' Hole

Age and/or high mileage is the most common cause of a weep plug hole leak.

Water pumps are inspected, and air pressure tested at the factory for any leaks. Per the manufacturer, all new water pumps have a break-in period. Shortly after startup, it is not uncommon for a new water pump to have slight seepage of coolant discharge coming from this hole below the water pump pulley. This is because the unique seal material in a new water pump is designed to 'bed in' as the impeller shaft spins. Slight weeping or dampness from or around the discharge 'weep plug' or cap is allowable for at least 100 miles after installation and should not be attributed to a defective water pump.

However, in extremely cold climates (below freezing), the correct coolant mixture ratios must be maintained. If the coolant ratio is incorrect, it can cause weakening of the machined weep hole tolerances causing a leak.

Audi Water Pump Noise

Users post videos of engine noises (whine, humming, squealing). Where is it coming from, they ask? Don't assume that the noise is coming from the water pump unless it has been leaking for some time. The possibility is very remote that the water pump is making the noise if it isn't leaking.

Many possibilities can account for front engine noises such as alternator bearing, AC compressor clutch bearing, viscous fan clutch bearing, serpentine belt tensioner(s), serpentine idler wheel, power steering pump, any other belt driven component, or lastly the timing belt tensioner idlers. A simple test is to remove the serpentine belt (which drives many of these components). If the noise goes away, it is a serpentine-related component. If the noise persists, then it may be something behind your Audi's timing belt cover.

"There is a noise coming from the front of my engine. Is it my water pump?"

It is normal for a new Audi water pump to make a light hum during the manufacturer's break-in period. Some aftermarket manufacturers that use cheaper internal bearings may make a slightly louder drone. Blauparts only supplies the highest quality Audi water pumps that are manufactured using the OEM internal bearings and seals. Another cause for this type of noise can be an over tensioned timing belt. Incorrect timing belt tension puts additional stress on the internal water pump bearings, causing a droning noise.

It is very rare for an Audi water pump to make a rough grinding bearing noise. However, driving with a leaking water pump for an extended period can produce this type of Audi water pump noise. At this point, the internal bearings have developed excessive play and the seals have already failed. Continued driving of the car could be catastrophic.

Engine Overheating

Some drivers experience random overheating issues and wonder if this is caused by the Audi water pump. Intermediate or random overheating is usually due to an obstruction in the cooling system or a sticky, malfunctioning thermostat. We recommend looking at the thermostat first.

Has the car been overheated either by you or the previous owner? Depending on the severity or how long it was driven in an overheated state (one instance will do it), your cylinder heads (possible warping) and head gasket (weakening) will be affected. Warped cylinder heads or weak head gaskets intermediately begin to seal and unseal, discharging cylinder compression into the cooling system and disrupting or preventing the flow of coolant. This is usually what can cause overheating, not the Audi water pump.

Overheating due to a water pump is very rare. There is the possibility that the Audi water pump impeller has begun to separate or break loose from the shaft. This can result in insufficient engine coolant flow and possible overheating, due to the impeller's inability to turn the same RPMs as the engine. Remove and inspect the water pump to see if the impeller has spun on the shaft. This was known to happen on earlier (pre-2000) models. See the Audi water pump plastic impeller controversy. Expand your knowledge regarding this debate by watching our video.

Audi Water Pump Diagrams - Audi water pump functionsAudi Water Pump Diagram and Functions

Circulating the coolant through the cooling system is the main function of an Audi water pump. The water pump driven by the timing belt circulates the coolant throughout the engine by the centrifugal action of a finned impeller on the Audi water pump shaft. As the engine runs, the timing belt revolves around the Audi water pump pulley, rotating the water pump impeller, which is within the cooling system, causing the coolant to circulate.

Where the Audi water pump was once a commodity product, it is now considered to be a crucial technical component of coolant and engine systems. In the course of engine development, the engineer's primary target is to achieve the BEST engine performance and efficiency. To accomplish this, the water pump needs to produce and maintain precise coolant circulation rates. These rates sustain optimal engine temperature, fuel economy, and emissions.

Although there has been major focus put on the water pump impeller, it is the internal bearings and seals that contribute to an Audi water pump life span. Some aftermarket manufacturers don't use the OEM-designed water pump bearings and seals. If your Audi model is designed to use specific water pump components, replacing them with ones of differing geometries, material, weight, shape, or profile will negatively affect the intended performance and reliability of your car. Blauparts only supplies the highest quality Audi water pumps that are manufactured using the OEM design and components (i.e. internal bearings, seals, impeller).

Blauparts supplies water pumps that use the OEM design. Including genuine OEM heavy duty bearings and seals (see Audi water pump diagrams). These pumps are individually tested using specific sealing porosity tests, involving resistance of the flange/pulley and impeller to axial movement. What does all this mean? Significantly greater reliability over other aftermarket pumps! This trusted company is the OEM (original equipment manufacturer) for BMW, Ferrari, Maserati, Alfa Romeo, Lancia, Fiat, and Ford (Europe). One more reason to look to Blauparts for all your Audi timing belt maintenance needs!

Correct installation is the biggest contributing factor in an Audi water pump's life span. Do you expect your water pump to last 60,000 to 90,000? When performing this crucial engine maintenance, it's important to take the time to re-create the condition of your engine as it was when it left the factory line. You cannot be lazy when it comes to timing belt and Audi water pump replacement! Cutting corners now adds time, labor, and money later. See our Blauparts Audi water pump replacement 'Service Bulletin'.

Audi Water Pump Replacement Intervals

Wondering if it's time to change your Audi water pump? It is important to follow the vehicle manufacturer's water pump replacement schedule. As a rule, timing belt and Audi water pump replacement should be done every 60,000 to 90,000 miles. An Audi water pump provides reliable service and is typically a maintenance-free part within its suggested life span. Since the water pump is a key component of the cooling system, changing it at the specified service interval is very important. Replacing the Audi water pump during a timing belt change is recommended. Remember that the timing belt and water pump work closely together (the timing belt runs the water pump) and have a similar life cycle. Audi water pump failure symptoms are often seen around timing belt replacement intervals. Therefore, Blauparts only sells the water pump in a complete Audi timing belt kit.

The older a vehicle gets (i.e. over 100,000 miles), regular inspection of the Audi cooling system becomes a more essential part of preventative maintenance. Checking the radiator, expansion tank, hoses and connections are often associated with high mileage engines.

Basic Overview of How to Change or Replace an Audi Water Pump

How to change replace an Audi water pumpThis is a basic overview of how to replace an Audi water pump and timing belt. The location of the water pump on most engines is directly behind the timing belt on the front side of the engine. Audi inline mounted engines must be put into the service position first. When the front bumper is removed, special tools are used to support the radiator valance, enabling the valance to slide out about 6-8 inches. The whole front of the engine is then accessible for repair. For transverse mounted Audi engines, the front of the engine is accessed through the passenger side wheel well and over the fender.

Remove all serpentine belt(s) and accessory belt components. Remove all timing belt covers. Set engine timing. Utilizing special factory tools that lock the crankshaft and camshaft in place is a crucial part of the replacement process. When this is complete, all the timing belt components, water pump, and thermostat can be replaced. Replace the timing belt, tensioners, idlers, tensioner damper, as well as any seals showing signs of leakage. All the timing belt components including the water pump have a similar service life of 60-90k and should be replaced at the same time.

The typical Audi timing belt replacement service takes between 6-10 hours of labor, dependent on the vehicle's engine and condition. The Audi water pump replacement cost will depend on each repair shop's hourly labor rate. When replacing an Audi water pump or timing belt, always refer to and follow the factory Robert Bentley manual. Blauparts recommends having an 'Audi VW Factory Trained ASE Certified Technician' install your parts.

Installation Note: During the Audi water pump and thermostat replacement, the coolant system needs to be thoroughly flushed (no shortcuts)! Thoroughly flushing the coolant involves flushing the engine block, radiator, and heater core. See the Blauparts Audi water pump replacement 'Service Bulletin' for details.

Please see the 'How to prevent your water pump from premature failure and leaking' page for some important DOs and DONTs of Audi water pump replacement