Please Note: The following service bulletin and Audi A4 crankshaft pulley / crank seal replacement information corresponds to STEPS 24-26 of our Audi A4 Timing Belt Installation Guide.
Audi A4 timing belt installation is a complex repair procedure and should be performed by experienced automotive technicians, trained in performing proper timing belt installation.
Blauparts recommends that an Audi VW Factory Trained ASE Certified Technician perform timing belt repair on your Audi A4. One who has been trained in timing belt procedures for your exact vehicle model. This is for your safety and to prevent improper installation by untrained and unqualified installers and technicians, which may lead to possible engine damage.
Always read the factory service manual safety instructions and guidelines.
ALWAYS WEAR SAFETY GLASSES AND OTHER SAFETY ITEMS WHEN PERFORMING THE FOLLOWING WORK!
All information and images © copyright of Blaufergnugen Inc.
How to prevent Audi A4 front crankshaft timing belt pulley key damage on 2.8L 30 valve engines?
PERTINENT TO: 1998-2005 V6 30 Valve Models With AHA, ATQ, APB, and BEL Engine Codes
Please read the following information BEFORE removing the Audi A4 front crankshaft timing belt pulley on your engine!
Blauparts has received reports of inadvertent damage occurring during the removal of the lower Audi A4 crankshaft timing belt pulley on 2.8L 30 valve engines. These engines have a lower timing belt pulley that utilizes a minimally sized ‘key’. This ‘key’ is devised to engage with the corresponding keyway in the crankshaft. See the photos below for indication on the location of the small key located on the lower timing belt pulley.
Some have reported that while loosening the main crankshaft bolt, existing friction, corrosion, rust, or more commonly stray thread locking compound, between the bolt head and pulley, can inadvertently cause the small ‘key’ to be damaged and in some cases completely twist off the pulley. Because this ‘key’ engages just the tip of the crankshaft, the crankshaft keyway can also be damaged.
Upon removal, it is crucial that you inspect the small ‘key’ protrusion found on the inside of the pulley for any damage. You must also inspect the very front edge of the crankshaft keyway for damage. If the Audi A4 crankshaft keyway shows signs of damage, it will no longer engage properly with the key on the pulley.
Short of complete replacement, it may be possible to locate a qualified welder and have the end welded up and ground to shape. We stock a Lower Crankshaft Timing Belt Pulley Kit because of this problem.
Blauparts warns that using a pulley that shows ANY signs of ‘key’ damage is unacceptable! If reinstallation is attempted with a damaged pulley ‘key’ or crankshaft keyway, the lower crankshaft timing belt pulley can easily fall out of time during main crankshaft bolt contraction, ultimately leading to catastrophic Audi A4 engine failure.
Due to the possibility of this damage, the installer may want to contemplate the need for the removal of the lower crankshaft timing belt pulley to access the front crank seal. If there is no indication of oil leakage from the front crank seal, the installer may want to leave the lower crankshaft timing belt pulley as is, not risking damage. However, if your Audi A4 front crank seal is leaking and needs to be replaced, you have little option but to remove the pulley. Please read more information below: Should I replace my Audi A4 crankshaft seal?
You may wish to forego crankshaft seal replacment during timing belt service IF the engine has low mileage and upon inspection the crank seal is 100% dry (see image). Seals can last up to 200,000 miles. If the crankshaft area is dry, the seal will typically last until the next timing belt service interval.
During Audi A4 crankshaft seal removal, there is a risk of scaring the area between the seal and crank mating area. This can cause irreversible damage to the crank, resulting in an unsealable crankshaft and subsequent oil leaks.
Pictured Example: Note the accumulated wet oil residue in the crankshaft seal area (Image 1A). Once the lower most timing belt crank cover was removed, a stream of oil is easily noticeable on the backside of the cover (Image 1B).
If your crankseal is leaking, it should be replaced. See Installation Steps 24-26.
All information and images © copyright of Blaufergnugen Inc.
Service BulletinsImportant Repair Information.
Please read the
following bulletins BEFORE beginning timing belt service.
- Subject: How to prevent premature water pump failure? Proper cooling system service procedures.
- Subject: How to prevent irreversible damage to the hydraulic tensioner damper? Proper hydraulic tensioner damper installation.
QuestionsDo you have a specific question regarding 2.8L Audi A4 timing belt replacement? We're here to help!
Troubleshooting GuideCommon installation problems.
Technical Help Coming Soon!
BLAU OFFICIAL O.E. INA Audi A4 Timing Belt KitsOur goal is to make your Audi A4 timing belt repair job a success. Preventing any possible problems during this crucial repair is our number one priority. Over 27 years of Audi German heritage and small family owned business way of thinking has strongly influenced our Gen II BLAU® Audi Timing Belt Replacement Kits.
Related Audi A4 Timing Belt Replacement Information
Installation StepsStep-by-step instructions on how to replace the timing belt on your Audi A4 2.8L 30 valve engine.
Cost of ReplacementHow long does it take and how much will it cost to replace the timing belt on my Audi A4 with 2.8L engine?
BLAU OFFICIAL O.E.™ ComponentsWhat are the brand names of the timing belt components that originally came on my Audi A4 2.8L 30 valve?
Change IntervalsWhat is the factory recommended timing belt interval for Audi A4 2.8L 30 valve engines? How long will new timing belt parts last after replacement?
Special ToolsDo I need special tools to replace the timing belt on the Audi A4 2.8L engine? Can I do it without the tools?
Related ReplacementCan I just replace the timing belt? What other parts should be replaced during Audi A4 timing belt service?